The Float Tube Fishing Forum We're Always On The Fish

Log in

I forgot my password



Latest topics

» Funky waders
by SP Dan Yesterday at 5:05 pm

» Music is your special friend
by jeffcpr Yesterday at 2:14 pm

» Our 7th Annual FTFF Toy Drive is now in effect
by jeffcpr Tue Nov 14, 2017 5:40 pm

» January's Tournament Changes!!
by jeffcpr Tue Nov 14, 2017 10:44 am

» Where to go for float tube fishing - Newport Harbor
by SP Dan Mon Nov 13, 2017 8:57 am

» Perris Lake
by GT Mon Nov 13, 2017 8:38 am

» Some stuff I got in trade
by Master Baiter Mon Nov 13, 2017 2:46 am

» Some pretty Awesome Decorative pieces
by Master Baiter Sat Nov 11, 2017 10:55 pm

» Welcome to Wader Skins
by Jerdon Sat Nov 11, 2017 7:05 pm

» What do you think Saltwater VS Freshwater should we?
by Misfitdog Sat Nov 11, 2017 5:19 pm

» Happy Birthday Marine Corps
by SP Dan Sat Nov 11, 2017 9:48 am

» How Much Does Your Fully Loaded FT Weigh?
by SP Dan Fri Nov 10, 2017 7:07 pm

Members benifits
Clearance Banner

Clearance Banner

Clearance Banner

Clearance Banner

Clearance Banner

Clearance Banner

Clearance Banner


You are not connected. Please login or register

FLOAT TUBE FISHING FORUM » Float Tubes, Pontoons and Related Equipment Discussions » Float Tube, Pontoon, and Equipment Related Discussions » Regular sonar mount for tubes

Regular sonar mount for tubes

View previous topic View next topic Go down  Message [Page 1 of 1]

1 Regular sonar mount for tubes on Wed Sep 04, 2013 9:06 am

Renegade


Bobber
Bobber
I have an older Hummingbird sonar that I love. I have gone from framed pontoons (which where pretty easy to figure out) to the FRAMELESS models.
I have three different models that are all different diameter so I need something that will adapt.
I have the RAMP mount which is a little pricey, and I do feel this can be done without the Ram system, but here is what I came up with
Parts are the Ram sonar plate, the flush mount ram ball, and a 4" extension. Also 6' of 2" nylon strap with two adjusters and one quick clip male and female.
18" of 1" PVC, 2" Carriage bolt and a wing nut for easy finger tightening.
Lastly, a flexible but little thicker cutting board.

Here is the mobile version I now use:
[You must be registered and logged in to see this image.]
[You must be registered and logged in to see this image.]
[You must be registered and logged in to see this image.]

I also use a small 12Volt rechargeable security battery to power it. Battery is about 4" x 3" X 2"

2 Re: Regular sonar mount for tubes on Wed Sep 04, 2013 9:20 am

jesusbm562

avatar
Junior
Junior
Pretty good idea and have you tried it out on the water?

3 Re: Regular sonar mount for tubes on Wed Sep 04, 2013 9:45 am

Renegade


Bobber
Bobber
Several times. Trick is to put it on the tube while it is under inflated then tighten the straps then inflate tube.

It is very secure.

[You must be registered and logged in to see this image.]

4 Re: Regular sonar mount for tubes on Wed Sep 04, 2013 9:57 am

fisheromen

avatar
Junior
Junior
Very nice! A couple tabs of Velcro under it would make it even more secure.

5 Re: Regular sonar mount for tubes on Wed Sep 04, 2013 10:00 am

Renegade


Bobber
Bobber
[You must be registered and logged in to see this link.] wrote:Very nice!  A couple tabs of Velcro under it would make it even more secure.

Absolutely! The cutting board I used has a rubbery back so it won't slide on counters.

6 Re: Regular sonar mount for tubes on Fri Sep 06, 2013 11:07 am

TheAsianGuy

avatar
Old Timer
Old Timer
Great job! Perfect to switch from tube to tube.

Sponsored content


View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum